GE washer repair in Toronto
Top-load and front-load GE washers repaired by certified technicians. Same-day service, upfront labour prices and $25 off when you book online.
Book your washer repair

Expert GE washer repair
GE washers are everywhere in Toronto condos and family homes. Reliable when maintained, they have a familiar set of wear items — which means we usually have the part on the truck.
Models we service: top-load and front-load washers — standard, high-efficiency and smart versions.
Common GE washer problems
What we see most often on GE machines — and the typical labour for each fix.
Typical faults
- Top-load that won’t agitate or switch to spin (shift actuator)
- Washer that won’t start because of a faulty lid switch
- Slow or no draining from a failing pump
- Water inlet valve problems and slow filling
- Loud banging from worn suspension
Technician tip
On GE top-loaders, a lid that closes crookedly is the cheapest “fault” to check before booking — but if it still won’t start, call us.
See typical pricesWhat a GE repair costs
Labour only — the same transparent ranges for every brand. Parts are quoted separately.
- Drive belt replacement$99–199
- Lid switch / door lock assembly$99–199
- Agitator dogs$99–199
- Water level / pressure switch$99–199
- Motor coupling$99–199
- Drain pump replacement$199–249
- Water inlet valve$199–249
- Motor control board$199–249
- Door boot seal / gasket$199–249
- Shock absorbers$199–249
- Tub bearing replacement$199–299
- Spider arm assembly$199–299
Quick diagnosis
Tell us what your GE is doing.
Won’t start
A washer that won’t power on is usually a faulty door latch or lid switch, a failed timer or a control-board fault. We test both the electrical and mechanical sides to pinpoint the cause.
for this problem$99–249
Won’t spin
If it fills but doesn’t spin, think worn belt, lid switch or a failed motor coupling. We check the drive system, transmission and spin control to get laundry moving again.
for this problem$99–249
Loud noises
Banging or roaring in a spin points to worn bearings, dampers or suspension — or something stuck in the drum. We run a full diagnostic before any part is touched.
for this problem$199–299
Leaking water
Leaks come from a handful of places: a split hose, a torn door boot, a failing pump or a worn tub seal. We find the exact source and give you a lasting fix.
for this problem$99–249
Won’t drain
Standing water usually means a clogged pump or filter, a blocked hose or a control fault. We clear the drain path and replace whatever has failed.
for this problem$99–249
Won’t fill
No water, or very slow water: a failed inlet valve, a bad water-level sensor or a control signal problem. We check the supply side and the electronics.
for this problem$99–249
Smells bad
Mould and bacteria love door gaskets and detergent drawers. We deep-clean, replace a damaged boot if needed and show you how to keep it fresh.
for this problem$99–249
Error code / dead display
Modern washers display codes for everything from door-lock failures to sensor faults. We decode the code for your exact brand and fix the cause, not just the symptom.
for this problem$179–249
Agitator won’t move
Top-load agitator limp while the motor hums? Stripped agitator dogs or a worn belt are the usual suspects, and both are fast fixes.
for this problem$99–199
How it works
Book online
Tell us the brand and the problem in about a minute. Booking online takes $25 off your repair.
We confirm a window
A technician is lined up for a same-day visit whenever availability allows — or the next available slot.
Diagnosis & fixed price
We find the fault, explain it in plain language and quote the full price. You decide — no pressure.
Repaired & tested
Genuine parts, a full test cycle and a satisfaction guarantee. The service call is waived when you repair.
GE washer repair near you
GE washer repair — FAQ
Do you repair GE washers in Toronto?
Yes. We repair GE top-load and front-load washers across Toronto and the GTA, with same-day visits whenever availability allows.
How much does a GE washer repair cost?
Labour for most GE washer repairs runs from $99 to $299 depending on the part — quick fixes like belts and lid switches are $99–$199, pumps and boards $199–$249, and major drum work up to $299. Parts are quoted separately and you approve the total first.
Are GE washers worth repairing?
Often yes. If the repair is under about half the price of a comparable new washer and the drum and tub are sound, repairing a GE is better value. We’ll give you an honest opinion on site.
Do you use genuine parts for GE washers?
Yes — manufacturer-approved parts, so the repair lasts and the washer performs as intended.
Book your GE washer repair
Book online in a minute — same-day service, upfront pricing and $25 off your repair.








